Promotech PRO 10 PB Operator'S Manual Download Page 31

Page: 31 / 31

PRO 10 PB (PBE)

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

8. WARRANTY CARD

WARRANTY CARD No

.............

........................................................................... in the name of Manufacturer warrants

the PRO 10 PB (PBE) Pipe Bevelling Machine to be free of defects in material and

workmanship under normal use for a period of 12 months from the date of sale.

This warranty does not cover tool bits as well as damage or wear that arise

from misuse, accident, tempering, or any other causes not related to defects in

workmanship or material.

Date of production .........................................................................................................

Serial number ................................................................................................................

Date of sale ...................................................................................................................

Signature of seller ..........................................................................................................

1.06 / 8 June 2015

WE RESERVE THE RIGHT TO MAKE CHANGES IN THIS MANUAL WITHOUT NOTICE

Summary of Contents for PRO 10 PB
































Search results

Summary of Contents for PRO 10 PB

Reviews:

Related manuals for PRO 10 PB

Brands by name

Popular brands

Promotech PRO 10 PB, Operator'S Manual

Search results

Summary of Contents for PRO 10 PB

Reviews:

Related manuals for PRO 10 PB

Brands by name

Popular brands