manualshive.com logo in svg

Promotech PRO 10 PB, Operator'S Manual, Page: 21 / 31

Share
Download
Promotech PRO 10 PB Operator'S Manual Download Page 21

 

PRO 10 PB (PBE) 

This document is protected by copyrights. 

Copying, using, or distributing without permission of PROMOTECH is prohibited.

 

21 

4.4.4. Operating 

Once  the  machine  with  the  attachment  is  clamped  inside  the  pipe,  use  the  13 mm 

combination wrench to rotate the draw nut 

1

 in such a way to move the cutting edge 

of the tool outside the flange outer diameter. Then, set the sprocket 

2

 in the position 

shown in Fig. 9, and push out both pivots of the tripper blocks 

3

 to engage them with 

the attachment. Rotate the spoke handles 

4

 to the right to set machining depth to not 

more than 0.5 

mm (0.02’’) from the pipe end, and start the motor.  

 

 

Fig. 9. 

Proper positioning of the flange facing attachment 

 

Once  facing  of  the  flange  end  is  finished,  turn  off  the  motor  and  wait  until  the 

rotation  stops. Then,  rotate the  spoke handles to the left to retract the  tool from the 

workpiece.  Clean  the  entire  surface  of  the  flange  end,  and  perform  several  more 

rotations to improve the finish of the surface with one tripper block engaged (retract 

the  pivot  of  the  second  tripper  block)  and  with  machining  depth  not  more  than 

0.25 

mm (0.01’’). 

 

Feed direction of the tool 

1 

2 

4 

3 

Summary of Contents for PRO 10 PB
































Reviews:

No comments