Promotech PRO 10 PB Operator'S Manual Download Page 18

Page: 18 / 31

PRO 10 PB (PBE)

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

4.4. Flange facing attachment

4.4.1. General information

Allows

facing

flanges

with

diameters

from

508

(3.54

–20’’)

with

the

machine

clamped inside a pipe with internal diameter either of 84

–269 mm (3.31–10.59’’)

using the standard expanding mandrel or of 219

–376 mm (8.62–14.8’’) using the

large expanding mandrel.

Flange diameter

–508 mm (3.54–20’’)

Automatic feed range

180.5 mm

(7.11’’)

Diameter of rotating parts 569.4 mm

(22.42’’)

Feed per rotation

0.33 mm (

0.013’’, with one tripper block engaged)

0.66 mm (

0.026’’, with two tripper blocks engaged)

4.4.2. Equipment included

Equipment of the flange facing attachment consists of the following elements.

Milling unit for flanges

1 unit

Holder with two tripper blocks

1 unit

Cutting insert

8 units

Fixing screw for cutting insert

2 units

Internal insert holder

1 unit

External insert holder

1 unit

Metal box

1 unit

M6x35 screw

3 units

M6x30 screw

3 units

M6x14 screw

3 units

5 mm hex wrench

1 unit

4 mm hex wrench

1 unit

3 mm hex wrench

1 unit

13 mm combination wrench

1 unit

T15 screwdriver

1 unit

Tool container

1 unit

Part number:
PRK-0447-00-00-00-2

Summary of Contents for PRO 10 PB
































Search results

Summary of Contents for PRO 10 PB

Reviews:

Related manuals for PRO 10 PB

Brands by name

Popular brands

Promotech PRO 10 PB, Operator'S Manual

Search results

Summary of Contents for PRO 10 PB

Reviews:

Related manuals for PRO 10 PB

Brands by name

Popular brands