Promotech PRO 10 PB Operator'S Manual Download Page 8 | Manualshive

Page: 8 / 31

background image

PRO 10 PB (PBE)

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

8

21. After every use, remove metal chips and excess coolant from

the

machine.

Never

remove

chips with bare hands. Clean the machine with a cotton cloth without

using any agents.

22. Cover steel parts with a thin grease layer to protect them against rust when not in

use for any extended period.

23. Maintain the machine and install/remove parts and tools only when the machine

is unplugged from the air (power) source.

24. Repair only in a service center appointed by the seller.

25. If the machine falls from any height, is wet, or has any other damage that could

affect the technical state of the machine, stop the operation and immediately

send the machine to the service center for inspection and repair.

26. Never leave the machine unattended during operation.

27. Remove from the worksite and store in a secure and dry location when not in

use, previously removing the tools from holders.

«
...
6
7
8
9
10
...
»

Summary of Contents for PRO 10 PB
































Reviews:

No comments

Related manuals for PRO 10 PB

Brand: GE Pages: 50

DC POWER-L Series

Brand: Salicru Pages: 32

Brand: ZALMAN Pages: 7

Aquajoe FIBERJACKET AJFJH50-58-PRO-RM

Brand: SNOWJOE Pages: 8

Brand: Wacker Neuson Pages: 62

Brand: Graco Pages: 2

Brand: Senco Pages: 32

Brand: Woodstar Pages: 116

Brand: QJE Pages: 7

Brand: M-system Pages: 2

Brand: Ironton Pages: 9

Brand: LIVARNO LUX Pages: 100

Brand: Mega Pages: 20

Brand: ZyXEL Communications Pages: 6

Brand: Puls Pages: 2

Brand: Kennedy Pages: 2

Brand: N2Power Pages: 10

Carlyle TW12RH2

Brand: Napa Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands