background image

» INSTALLATION INSTRUCTIONS

 / OCTO / OCTO + / HEXA

22

proswell.fr

Check that the upper, inner part of the tank is clean. 

Remove the protective cap from the collector tube.

To facilitate fitting of the lid, grease the interior of the 

top part of the tank (silicon grease). 

Position the lid flat over the tank and push down evenly 

to engage the lid into the tank. 

Once in position, the lid should be up against the top 

of the tank and the o-ring should no longer be visible.

     

Screw the holding ring into position to keep the lid in 

position. 
 

Hand tighten by a quarter turn.

  CAUTION :

An incorrectly fitted lid could have the following reper-

cussions:
- Discharge of sand through the return fitting 

- Water leaking from the waste outlet.

- Leaks from the filter tank.
In filtration mode, a weak flow from the waste outlet is 

normal. 

>>      

                 

FILTER ASSEMBLY (CONT.)

>>      

                 

CONNECTING THE SKIMMER AND RETURN FITTING

55

56

Wrap teflon (not provided) 3 times around the 
threading on the barbed union before screwing it onto 
the skimmer body. Push the pump suction tube onto 
the skimmer’s barbed union and hold it in position 
using a collar clamp.

Push the filter return tube onto the return fitting’s 
barbed union land hold it in position using a collar 
clamp.

Waste

Outlet, filtered water

Inlet, unfiltered water

Summary of Contents for Proswell Tropic HEXA









































Reviews: