background image

4

UL/c-UL(CSA) Application Notes

CE Marking Notes

The GLC150-BG41-RSFL-24V is a UL/c-UL listed product.
(UL file No. E214883)
This unit conforms as a component to the following standards:

„

UL508

Industrial Control Equipment

„

UL1604

Electrical Equipment for Use in Class I and II Division 2 and Class III Hazardous (Clas-
sified) Locations

„

CAN/CSA-C22.2, Nos.1010

Standard for Safety of Information Technology Equipment, including Electrical Busi-
ness Equipment

GLC150-BG41-RSFL-24V (UL Registration Model : 2980036-03)

<Cautions>

If the LogiTouch is installed so as to cool itself naturally, be sure to install it in a vertical
panel. Also, be sure that the LogiTouch is mounted at least 100mm away from adjacent
structures and other equipment, otherwise, the heat generated by the LogiTouch's inter-
nal components may become higher than that allowed by UL standard requirements.
The LogiTouch shall be separated from the mains by double or reinforced insulation.

UL1604 Conditions of Acceptability and Handling Cautions:

1. Power, input and output (I/O) wiring must all be in accordance with Class I, Division 2

wiring methods, Article 501-4 (b) of the National Electrical Code, NFPA 70, or as speci-
fied in Section 18-152 of the Canadian Electrical Code for units installed within Canada,
and in accordance with that location's authority.

2. Suitable for use in Class I, Division 2, Groups A, B, C and D hazardous locations, or

nonhazardous locations only.

3. WARNING: Explosion hazard - substitution of components may impair suitability for

Class I, Division 2.

4. WARNING: Explosion hazard - do not disconnect equipment unless power has been

switched OFF or the area is known to be nonhazardous.

5. WARNING: Explosion hazard - when in hazardous locations, turn OFF power before

replacing or wiring modules.

The GLC150-BG41-RSFL-24V is a CE marked, EMC compliant product. This unit also
conforms to EN55011 Class A, EN50082-2 directives.
For detailed CE marking information, please contact your local LogiTouch distributor.

CNS Notes

The GLC150-BG41-RSFL-24V conforms as a component to the following standards:
• CNS 13438 (Class A)
<Cautions>

The LogiTouch unit is designated as Class A industrial equipment. Therefore, when
using this unit in a residential area, be careful to avoid electromagnetic interference
from nearby home appliances.

Summary of Contents for LogiTouch GLC150-BG41-RSFL-24V













Reviews: