background image

5

Package Contents

The following items are included in the LogiTouch's package. Before using the
LogiTouch, please confirm that all items shown here are present.

„

„

„

„

„

Installation Fasteners (4)

This unit has been carefully packed, with special attention to quality. However,
should you find any of the items shown here to be damaged or missing, please
contact your local LogiTouch distributor immediately.

„

„

„

„

„

LogiTouch Type-C (1)
(GLC150-BG41-RSFL-24V)

„

„

„

„

„

Installation Guide (1)
<This Guide>

Option Items (sold separately)

„

„

„

„

„

LogiTouch Series
User Manual
(GLC150-MM01)

„

„

„

„

„

Flex Network Cables

„

„

„

„

„

Logic Program Developer Software
LogiTouch Editor

„

„

„

„

„

Data Transfer Cable (GPW-CB02)

50m

FN-CABLE2050-31-MS

200m

FN-CABLE2200-31-MS

„

„

„

„

„

External Communication Unit Connec-
tion User Manual
(GPW-MC50M)

Phoenix Contact

MC1, 5/6-STF-3,81

Digital Elec. Corp.

FN-IFCN01

(5 pieces)

„

„

„

„

„

Maintenance Option
Flex Network I/F Connectors

1

 Part Names

The LogiTouch Type-C’s part names and their functions are explained below.

A : Display: Displays controller and user-

created screen data.

B : Touch Panel : Performs touch-initiated

screen change operations and sends data
to controller.

A,B

C

Summary of Contents for LogiTouch GLC150-BG41-RSFL-24V













Reviews: