background image

4

The Dip Switches and Slide Switch are located in the bottom of the FP unit. Only the 
settings when the power supply is turned on is effective to the Dip Switches and the Slide 
Switch. After changing the settings of the Dip Switches and the Slide Switch, be sure to 
restart your FP unit 

„

SW1

• SW1-2    Dip Switch SW1-2 is used to display or hide the OSD.

 

To hide the OSD, set the switch to ON. To display the OSD, set the switch to OFF.

 

The default setting is OFF. (OSD is displayed.)

„

SW2

2

Dimensions

3

Dip Switches and Slide Switch

Switch

Setting

SW1-1 Reserved (Always OFF)
SW1-2 Display/Hide the OSD
SW1-3 Reserved (Always OFF)
SW1-4 Reserved (Always OFF
SW1-5 Reserved (Always OFF)
SW1-6 Reserved (Always OFF)
SW1-7 Reserved (Always OFF)
SW1-8 Reserved (Always OFF)

Switch

Setting

Slide Switch is used to switch the data input/output (command 
control) method on the touch panel between USB and RS-232C 
(Serial). The default setting is RS-232C.

301[11.85]

317[12.48]

243[9.57]

227[8.94]

58[2.28]

8[0.31]

Top View

Front View

Side View

Unit: mm [in]

Dip Switches(SW1)
Slide Switch(SW2)

Bottom View

ON

1

8

SW1

2

32

U

SB

Summary of Contents for FP3650-T41

















Reviews: