manualshive.com logo in svg

Prism Sound ADA-8, Module Reference

Share
Download
Prism Sound ADA-8 Module Reference Download Page 53

Prism Sound ADA-8XR Multi-channel A/D D/A Converter   Module Reference - Revision 1.01 

© Prism Media Products Limited, 2001-2005    

Page 3.52 

9.6  Module Dependent Factory Stores 

 
A selection of Factory Stores have been created for various applications of the FireWire I/O 
Module, they are described below. 
 
 

9.6.1  Analogue to Digital / Digital to Analogue (+ Digital) 

 
If your ADA-8 is fitted with a single FireWire I/O Module, the “FireWire AD/DA” store will 
appear in the store banks when the Factory Stores are recalled. Use this store for common 
A/D and D/A applications with sample rates up to and including 96kHz. 
 
When this store is recalled the FireWire I/O Module is configured for 8 in / 8 out operation. 
Giving a total of 8 input channels and 8 output channels. 
 
If you have an ADA-8 XR and wish to use this store with sample rates above 96kHz, you can 
do so by adjusting the FireWire I/O configuration to 4 in / 4 out as described in section 9.5.2. 
The unit will operate as before, except that input and output channels 5 to 8 will not be active. 
 
Path 1 is configured for analogue to digital conversion. The path synchronization source and 
sample rate are controlled by the workstation. See sections 9.7 and 9.8 for further information 
on controlling the ADA-8 from the workstation. 
 
Path 2 is configured for digital to analogue conversion. The path is synchronized to the 
FireWire I/O Module and the path sample rate is set to ‘=Ext’. These settings ensure that 
Path1 and Path 2 are synchronous. 
 
Note that if an AES3 I/O Module is also fitted to the ADA-8, Path 2 will be set up to use both 
the analogue and AES3 outputs. 
 
 

9.6.2  16 Channel Analogue to Digital 

 
If your ADA-8 is fitted with two FireWire I/O Modules, and two Analogue Line Input Modules, 
the “FireWire 2xADC” store will appear in the store banks when the Factory Stores are 
recalled. Use this store for 16 channel A/D applications with sample rates up to and including 
96kHz. 
 
When this store is recalled each FireWire I/O Module is configured for 8 in / 2 out operation. 
Giving a total of 16 input channels and 4 dummy output channels (the dummy output 
channels are required to maintain synchronization between FireWire I/O modules). 
 
Path 1 is configured for analogue to digital conversion. The path synchronization source and 
sample rate are controlled by the workstation. 
  
Path 2 is configured for analogue to digital conversion. The path synchronization source and 
sample rate are controlled by the workstation. 
 
See sections 9.7 and 9.8 for further information on controlling the ADA-8 from the workstation. 
 
 

9.6.3  16 Channel Digital to Analogue 

 
If your ADA-8 is fitted with two FireWire I/O Modules, and two Analogue Line Output Modules, 
the “FireWire 2xDAC” store will appear in the store banks when the Factory Stores are 
recalled. Use this store for 16 channel D/A applications with sample rates up to and including 
96kHz. 
 

Summary of Contents for ADA-8
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands