manualshive.com logo in svg

Prism Sound ADA-8, Module Reference

Share
Download
Prism Sound ADA-8 Module Reference Download Page 35

Prism Sound ADA-8XR Multi-channel A/D D/A Converter   Module Reference - Revision 1.01 

© Prism Media Products Limited, 2001-2005    

Page 3.34 

 

7.7  Interconnection and Synchronization 

 
In general, a single ADA-8XR with Pro Tools HD I/O Module is connected to the Pro Tools|HD 
in exactly the same way as a 192 I/O.  If pairs of ADA-8XRs are to emulate a single 192 I/O, 
or if 16AD or 16DA ADA-8XRs are to be used, it is important to follow the connection 
schemes detailed below.  
 
Having connected each ADA-8XRs as shown, the appropriate Store must be loaded as 
described in each section.  The Store is loaded by pressing the ‘Bank’ button to select the 
desired Bank, and then the Store number button.  When the desired Store name is displayed, 
press the ‘Enter’ key. 
 
 

7.7.1  Connecting a Single ADA-8XR as a 192 I/O 

 
Connect the Primary Port of the ADA-8XR’s Pro Tools HD I/O Module to the desired Core or 
Process card in the workstation using a standard DigiLink cable.  A further Digidesign or 
Prism Sound I/O can be connected to the Expansion Port in the usual way. The Wordclock 
I/O BNC connections on the ADA-8XR’s Utility Module can be used for Loop Sync I/O if 
required. 
 

 
Having connected the ADA-8XR as above, switch it on and load the ‘

ProT HD Main

’ Store. 

This is located in Bank 1, Store 1 for ADA-8XRs without additional digital I/O, and in Bank 3, 
Store 1 for ADA-8XRs with additional I/O. 
 
 

7.7.2  Connecting a Pair of ADA-8XRs as a Single 192 I/O 

 
The ‘first’ ADA-8XR (i.e. the one which will carry the earlier-numbered channels) is 
designated ‘Sub’, the other as ‘Main’. Connect the Primary Port of ‘Sub’ to the desired Core or 
Process card in the workstation, and the Expansion Port of ‘Sub’ to the Primary Port of ‘Main’ 
using standard DigiLink cables.  A further Digidesign or Prism Sound I/O can be connected to 
the Expansion Port of ‘Main’ in the usual way. The Wordclock I/O BNC connections on ‘Main’s 
Utility Module can be used for Loop Sync I/O if required.  NOTE: no sync connections are 
required on ‘Sub’.  It should not be included in any Loop Sync scheme. 
 

Summary of Contents for ADA-8
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands