manualshive.com logo in svg

Prism Sound ADA-8, Module Reference

Share
Download
Prism Sound ADA-8 Module Reference Download Page 33

Prism Sound ADA-8XR Multi-channel A/D D/A Converter   Module Reference - Revision 1.01 

© Prism Media Products Limited, 2001-2005    

Page 3.32 

7.3  Getting Started with Pro Tools|HD 

 
To get started quickly, if your ADA-8XR is already equipped for Pro Tools|HD, go straight to 
section 7.7. and follow the connection and configuration instructions. 
  
 

7.4  Fitting the Module 

 
NOTE: In most cases, the Pro Tools HD I/O Module (or Modules) have been factory-fitted so, 
unless you are fitting the module yourself, the remainder of this section may be ignored. 
 
The Pro Tools HD I/O Module can be fitted to either Digital I/O Slot (DIO1 or DIO2) in the rear 
of the ADA-8XR (as shown in the Layout section of the Operation Manual). Although the 
ADA-8XR can automatically accommodate the module in either position, it is conventional 
that workstation digital I/O modules are fitted in the upper slot (DIO1), with a general-purpose 
digital I/O module (e.g. AES3) fitted in the lower slot (DIO2) if any is required.  This will 
provide compatibility with operating examples quoted in these manuals.  Where an ADA-8XR 
is to be configured for 16 channels of A/D or 16-channels of D/A operation, TWO Pro Tools 
HD I/O Modules are required, one in each DIO slot. 
 
For details of how to fit the Module(s), refer to the Adjustments and Upgrades section of the 
Operation Manual. 
 
Having fitted the Pro Tools HD I/O Module(s), it will be necessary to ‘Reload Factory Default 
Stores’ so that the necessary ADA-8XR Stores for Pro Tools|HD operation become available.  
This is done through the ‘Preferences’ menu, as described in the ADA-8XR Operation 
Manual. 
  
 

7.5  Module Dependent Preferences Menus 

 
NOTE: This section describes additional menus which are available in ADA-8XRs fitted with 
Pro Tools HD I/O Modules.  However, in normal use it is not necessary to access these 
menus since loading the relevant Stores, as described in the following sections, automatically 
selects the correct states of these menus. 
 
If one or more Pro Tools or Pro Tools HD I/O Modules are fitted to an ADA-8XR, the 
‘Workstation Remote Control’ and ‘HD Workstation Main/Sub’ menus become available in the 
‘Module Dependent Preferences’ section of the Menu System.  
 
 

7.5.1  Workstation Remote Control menu 

 
 
 
 
This single selection menu allows the workstation remote control interface to be enabled or 
disabled. When enabled (set to ‘

On

’), various parameters of the ADA-8XR can be remotely 

controlled from Pro Tools|HD, as described in section 7.8.  When disabled (set to ‘

Off

’), 

adjustments made from the workstation are ignored by the ADA-8XR.  NOTE: It is strongly 
recommended that remote control is ALWAYS ENABLED for use with Pro Tools|HD, since 
there are many situations in which the system may fail otherwise.   
 
Note that this setting is automatically set to the ‘

On

’ state when Pro Tools|HD specific Factory 

Default Stores are loaded, as described in section 7.6.  
 
 

Wrkst Remote: On 
On Off 

Summary of Contents for ADA-8
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands