background image

Printed in USA 4/06 © 2006

2

625-525revG-EN

Steamer
625-OS

Safety Information

Indicates information important to the proper operation of the 
unit. Failure to observe may result in damage to the equipment 
and/or severe bodily injury or death. 

Indicates information important to the operation of the unit. Failure to 
observe may result in damage to the equipment.

WARNING

CAUTION

Important

Prince Castle reserves the right to change specifications and 
product design without notice. Such revisions do not entitle the 
buyer to corresponding changes, improvements, additions or 
replacements for previously purchased equipment.

Installation

Remove the unit from the carton and inspect for signs of damage. If there 
is damage to the unit:

notify the carrier within 24 hours of delivery

save carton and packaging materials for inspection purposes

contact your local dealer, or if purchased directly, the Prince Castle 
Sales Department at 800-722-7853 or 1-630-462-8800 to arrange for a 
replacement unit.

Regulator Assembly (625-276S) is packed separately in the box. The 
regulator is designed to be attached to the back of the prep cell.

NOTE: When installing this unit, the ambient temperature at the mounting 
site should not exceed 37.8°C (100°F).

All electrical connections must be in accordance with local electrical codes 
and any other applicable codes.

Plug the unit into an applicable electrical receptacle. Connect the water 
line to the back of the unit.

Water connection must provide maximum water pressure of 20 – 30 psi 
(138 – 207 kPa).

CAUTION

CAUTION

Operation

A.  Turn unit power On/Off switch to ON position. The display 

flashes all segments for 3 seconds. Then display will show 

PRINCE CASTLE

 for seven seconds.

B.  After ten seconds the display will show 

PR.E-HEAT

.

1

NOTE: The next-to-left most decimal point appears indicating power is 
applied to the platen. Platen will heat to the setpoint temperature.

Place the spatula fully into the unit and press the START button.

A beep will sound and the display will start to count down the 
steam cycle.

3

A. When the unit reaches the setpoint temperature, display will 

show the product name assigned to button 4.

B.  Pull out the spatula and place meat preset on the spatula 

insert.

2

When steam cycle is complete, the unit will sound a tone and 
the display will flash 

REMOVE

Pull out the spatula and remove the finished product.

4

Summary of Contents for 625-OS



















Reviews: