background image

625-525revG-EN

17

Printed in USA 4/06 © 2006

Steamer

625-OS

Planned Maintenance System: 
Maintenance Requirement Card 
(MRC) 

When
Daily

Tools

McD

®

 All Purpose Super 

Concentrate (APSC)

McD

®

 Sink Pak Sanitizer 

(KAYQUAT)

McD

®

 Delimer™ (as required)

Clean Sanitized Towel

Steamer Brush

Small Coffee Cup (as required)

Heat Resistant Gloves

STEAMER

Prince Castle: Rapid Steamer Series

Precaution

Hazard Communication Standard (HCS) — The procedure(s) in this 
manual include the use of chemical products. These chemical products 
will be highlighted with italic-faced letters followed by the abbreviation 
(HCS). See Hazard Communication Standard (HCS) manual for the 
appropriate Material Safety Data Sheet(s).

Daily Cleaning

1.

Turn the steamer power On/Off switch to the OFF position and unplug the 
steamer from the power source. 

“PROCEED WITH CAUTION” —

CAUTION UNIT IS STILL HOT

.

2.

While wearing protective gloves, remove the top cover, top cover plate and 
venturi plate and wash in a solution of 

McD

®

 APSC/APC

 made up in the 

back sink. Rinse with clean water, sanitize with 

McD

®

 Sink Pak Sanitizer 

(KAYQUAT

®

)

, and air dry.

NOTE: Do not use abrasive materials to clean the spatula insert or spatula.

3.

Wipe the steam chamber surface with a clean sanitized towel.

4.

If the surface shows signs of excessive calcium and lime buildup, 
deliming is required. Refer to the monthly cleaning and deliming 
procedure on page 2.

5.

Reassemble the steamer.

6.

Turn unit on. When unit is preheated, run a minimum of four cycles to prime 
the unit and remove any residual cleaner.

DO NOT SPRAY DIRECTLY ON THE UNIT OR USE ABRASIVE 
CLEANERS.

It is recommended that the steamer be delimed once a month. Some 
hard water areas may require daily, weekly, or biweekly deliming 
based upon actual buildup. Continued water problems may require 
further water treatment (use of the CUNO RO System FSTM035.) 
With use of the CUNO RO System FSTM035, deliming is 
recommended once a month.

Summary of Contents for 625-OS



















Reviews: