Primera CD Color Printer II User Manual Download

Page: 52 / 56

48 Interfacing Information

D. 6-PIN MINICIRCULAR AUXILIARY INTERFACE

The 6-pin minicircular auxiliary interface is used for connecting
the printer with auxiliary equipment such as a CD transporter/
auto-loader.

Pin assignments are as follows:

Uses 5v logic @ 5mA

Pin Number

Signal Description

Busy - Output is high when the printer is busy
or moving the CD Tray.

Tray Out - Output is high when the CD Tray
is fully ejected.

Tray In - Output is high when the CD Tray is
fully inserted.

CD In - Output is high when the CD Tray is in
and a CD is present.

Ground.

Tray In/Out - A low input moves the CD Tray
in if it is out, and out if it is in.

TABLE A-3: Auxiliary Interface Pin Assignments

510198 Fargo/CD Color PrtrII 2/26/99 12:36 PM Page 48

Summary of Contents for CD Color Printer II
























































Search results

Summary of Contents for CD Color Printer II

Reviews:

Related manuals for CD Color Printer II

Brands by name

Popular brands

Primera CD Color Printer II, User Manual

Search results

Summary of Contents for CD Color Printer II

Reviews:

Related manuals for CD Color Printer II

Brands by name

Popular brands