Primera CD Color Printer II User Manual Download | Manualshive

Page: 11 / 56

background image

Ink Cartridges and Printable CDÕs 7

Loading a Blank Jewel Case Booklet or Insert

Blank CD jewel case booklets and inserts are available for
creating custom jewel case labels. The jewel case booklet is
what slips into the top lid of the jewel case. The jewel case
insert is what is enclosed along the spine and back of the jewel
case. To load either, refer to the following:

1.

With the printerÕs front cover shut, press and release the

CD Tray button.

2.

Once the CD Tray is fully extended, place the blank jewel
case media into the CD TrayÕs securing clips as shown
below. Be sure to read the instructions printed on the
media for a description of which tear-off sections of the
media to remove before and/or after printing.

First insert leading edge into printer.

Then, pull back and secure beneath securing clips.

510198 Fargo/CD Color PrtrII 2/26/99 12:36 PM Page 7

«
...
9
10
11
12
13
...
»

Summary of Contents for CD Color Printer II

























































Reviews:

No comments

Related manuals for CD Color Printer II

Brand: CAB Pages: 263

Brand: Olympus Pages: 2

Brand: Olympus Pages: 148

WorkCentre Pro 90

Brand: Xerox Pages: 36

Brand: Xerox Pages: 2

Brand: Aficio Pages: 188

Brand: Oki Pages: 198

Brand: SEWOO Pages: 13

Brand: W2P Engineering Pages: 40

Magicard Opera 100

Brand: Ultra electronics Pages: 2

VERSAJET MP3200 Series

Brand: Cino Pages: 18

Brand: Oce Pages: 66

Brand: Ricoh Pages: 120

Brand: Kyocera Pages: 44

Brand: Ice Pages: 114

Brand: Epson Pages: 4

Brand: Epson Pages: 4

Brand: Nexa Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands