Presys PCON-Y17 Series Technical Manual Download Page 5

Page: 5 / 68

PRESYS



Instruments

PCON-Y17

Table of Contents

1 - Introduction ............................................................................................................... 1

1.1. General Description ............................................................................................... 1

1.2. Technical Specifications ......................................................................................... 2

1.3. Special Software Features ..................................................................................... 4

1.4. Order Code ............................................................................................................ 5

1.5. Parts Identification .................................................................................................. 6

2 - Calibrator Operation.................................................................................................. 7

2.1. Calibrator Menu ...................................................................................................... 8

2.1.1. Pressure Control Module

– Connections ......................................................... 9

2.1.2. Measure Mode ............................................................................................... 14

2.1.3. Control Mode ................................................................................................. 16

a) Range Parameters ........................................................................................... 17

b) Changing the setpoint ...................................................................................... 18

c) Stabilization Settings ........................................................................................ 19

d) Control Settings ............................................................................................... 19

e) Preset Setpoints .............................................................................................. 21

f) Step Function ................................................................................................... 22

g) Nudge Function ............................................................................................... 23

2.1.4. Vent Mode ..................................................................................................... 24

2.1.5. Absolute Mode ............................................................................................... 27

2.1.6. Changing the Pressure Unit ........................................................................... 28

2.1.7. Filter Intensity ................................................................................................ 29

2.1.8. Auxiliar Input .................................................................................................. 30

2.1.9. Transmitter Power Supply (TPS) ................................................................... 33

2.1.10. Auxiliary Input Scale Function ...................................................................... 33

2.1.11. Calibration Examples ................................................................................... 35

a) Pressure Transmitter Calibration ..................................................................... 35

b) Pressure Switch Verification ............................................................................ 36

2.1.12. Leakage / Stability Test ............................................................................... 38

2.2. HART

................................................................................................................. 40

2.2.1. HART

Connections ....................................................................................... 40

2.2.2. Starting Communication ................................................................................ 42

2.2.3. Adjusting the Measurement Range of a HART

Transmitter .......................... 43

2.2.4. Adjusting the Measurement Range of a HART

Transmitter with Reference

(CH Option) ............................................................................................................. 44

2.2.5. Checking / Adjusting HART

Transmitter mA Output ..................................... 45

presys

Summary of Contents for PCON-Y17 Series





































































Search results

Summary of Contents for PCON-Y17 Series

Reviews:

Related manuals for PCON-Y17 Series

Brands by name

Popular brands

Presys PCON-Y17 Series, Technical Manual

Search results

Summary of Contents for PCON-Y17 Series

Reviews:

Related manuals for PCON-Y17 Series

Brands by name

Popular brands