PRESSCON LOX, User Manual

Page: 22 / 46

22
No. Error message display row 1 Error message display row 2 Description Source message
74 Serial uart 3 frame buffer Serial connection 3 message buffer full ERR_UART3_FRAMEBUFF
75 Serial uart 7 receive fault Serial connection 7 receive error ERR_UART7_RX
76 Serial uart 7 transmit fault Serial connection 7 send error ERR_UART7_TX
77 Serial uart 7 frame length Serial connection 7 message length ERR_UART7_FRAMELEN
78 Serial uart 7 frame check Serial connection 7 message check error ERR_UART7_FRAMEBCC
79 Serial uart 7 frame buffer Serial connection 7 message buffer full ERR_UART7_FRAMEBUFF
80 Serial uart 8 receive fault Serial connection 8 receive error ERR_UART8_RX
81 Serial uart 8 transmit fault Serial connection 8 send error ERR_UART8_TX
82 Serial uart 8 frame length Serial connection 8 message length ERR_UART8_FRAMELEN
83 Serial uart 8 frame check Serial connection 8 message check error ERR_UART8_FRAMEBCC
84 Serial uart 8 frame buffer Serial connection 8 message buffer full ERR_UART8_FRAMEBUFF
85 CAN-bus 1 transmit buffer CAN-bus 1 send buffer full ERR_CAN1_TXFIFO
86 CAN-bus 1 bus fault CAN-bus 1 bus error ERR_CAN1_BUSERROR
87 CAN-bus 1 message lost CAN-bus 1 message missed ERR_CAN1_MSGLOST
88 CAN-bus 2 transmit buffer CAN-bus 2 send buffer full ERR_CAN2_TXFIFO
89 CAN-bus 2 bus fault CAN-bus 2 bus error ERR_CAN2_BUSERROR
90 CAN-bus 2 message lost CAN-bus 2 message missed ERR_CAN2_MSGLOST
91 Eeprom memory base check Eeprom memory error ERR_EEPROM_BASE
92 Eeprom memory address out of range Eeprom memory address fault ERR_EEPROM_ADDRESS
93 Eeprom memory read/write error Eeprom memory read / write fault ERR_EEPROM_READWRITE
94 Configuration base check Configuration fault ERR_CONFIG_BASE
95 Configuration checksum check Configuration check fault ERR_CONFIG_CHECKSUM
96 Configuration first boot Configuration first boot ERR_CONFIG_FIRSTBOOT
97 Configuration settings Configuration settings fault ERR_CONFIG_SETTINGS
98 CAN-bus network double devicenr Double device number found on CAN-bus ERR_NETWORK_DOUBLEDEVICENR
99 CAN-bus network unknown device Unknown device detected ERR_NETWORK_UNKNOWNDEVICE
100 CAN-bus network softwareversion Software version of other device does not match ERR_NETWORK_SOFTWAREVERSION
101 Main power rebooted Print has rebooted ERR_POWER_BOOTED
102 PSE mainpower backup power down
Mainpower was lost, system runs on backup
power
ERR_POWER_POWERDOWN
103 PSE mainpower backup pse failure / fault PSE power supply gives an error ERR_POWER_FAULT
104 PSE mainpower backup battery fault PSE battery gives an error ERR_POWER_BATTERY
105 Clock communication fault Communication with the RTC goes wrong ERR_RTC_COMM
106 Clock not set Clock not set ERR_RTC_NEW
107 Software fault timer handler Fault at internal timer ERR_TIMER_HANDLER
108 Software fault ppg handler Fault at internal pulse generator ERR_PPG_HANDLER
109 No ECD display message Reserved error ERR_RESERVED109
110 Device disabled Device is disabled ERR_DEVICEDISABLED
111 No ECD display message Reserved error ERR_RESERVED111