background image

page no. 15 of 36

Vision Maxi

 User Instructions  Doc Ref M609 issue 1.0 June 2021.

 Accompanying  material

They are included with the appliance, inside the packaging:

Check the presence of the individual components.

External fixed grid for air inlet and outlet (2 pcs front view)

Screws and dowels kit (6 pcs)

Wall mounting bracket

Control panel user manual

Remote control

Paper template for holes

CR2025 3V remote control battery

Wall inlet pipes (2 pcs)

Energy efficiency label

Control panel installation manual 

Internal flanges

C

D

A++
A

I

F

E

B

K

G

A

H

J

2.7    Handling without packaging

 Preliminary  warnings

The appliance must be handled only by qualified 

personnel, adequately equipped and with equipment 
suitable for the weight and dimensions of the appliance.

The appliance is unbalanced on the right (compressor 

side)

 Movement  methods

The unit can be moved manually for short distances. In 

this case it is necessary to check carefully that the weight 

of the unit does not exceed the regulations in relation to 
the number of people used.

2.8    Installation  site

The location of the appliance must be determined by 
the plant engineer or a competent person and must take 
into account both purely technical requirements and any 
national/local legislation in force.
This appliance is designed for vertical, low-wall or high-wall 
indoor installation.

 The appliance must be installed against a wall 
communicating with the outside. 

The appliance is stated as having an IPX0 protection 

rating, therefore it is not suitable for outdoor installation 
and in rooms with presence of water (swimming pool 
rooms, etc.).  

 Preliminary  warnings

Avoid installing the unit near:

•  obstacles or barriers that cause recirculation of the exhaust 

air

•  narrow places where the sound level of the appliance can 

be enhanced by reverberations or resonances

•  environments with the presence of flammable or 

explosive gases

•  very humid environments (laundries, greenhouses, etc.)

•  environments with aggressive atmospheres

•  solar radiation and proximity to heat sources

Summary of Contents for Vision Maxi





































Reviews: