background image

19

RADIO CONTROL INSTALLATION

A three or four wire radio control 

receiver can be installed on this 

operator. This radio control receiver 

can only be used to open the gate, 

therefore the TIMER TO CLOSE option 

must be activated for closing.

ACCESSORY CONNECTIONS

NOTE: If your radio’s connecting wires are not color coded as shown, see the radio’s 

installation manual to determine which wires are for the normally open contacts and which 

require the 24VAC Power Supply.

GREY

BLACK

RED

24 VAC

GREY

N.O.

CONTACT

4 WIRE 

RADIO

SINGLE BUTTON

COMMON

TERMINAL A

TERMINAL B

LOOP DETECTOR SYSTEMS AND INSTALLATION

The diagram on the right depicts the 

typical loop options for a Swing Gate 

installation.

1.  The Exit Loop provides a signal 

to open the gate when a vehicle 

enters the loop zone.

2.  The Reversing Loop protects 

a vehicle in the loop zone from 

being contacted with the gate by 

overriding any close signal while 

the gate is open, and by reversing 

the gate if closing.

3.  The Shadow Loop protects a 

vehicle in the loop zone from 

being contacted with the gate 

by overriding any close signal 

while the gate is in the full open 

position.

4'

4'

4'

4'

4'

4'

4'

Road Surface

3/16” to 1/4”

Saw Slot

Sealant

Min 1”

Approx.

10’

Loop Wires

LOOP INSTALLATION 

1.  Lay out the desired loop locations per the diagram. The standard size chart on the 

following page will give an approximate length of wire required for various loop 

dimensions and number of turns required.  

FIGURE 13

Summary of Contents for rsw





























Reviews: