background image

18

MASTER-SLAVE INSTALLATION

NOTE: A single unit is considered a 

Master. In a Master/Slave installation, 

one unit must be converted to LEFT 

HAND operation.

1.  Place jumper on the Master 

operator’s control board in the  

OFF position.

2.  Place jumper on the Slave operator’s 

control board in the ON position.

3.  Connect Terminal #15 of Master unit 

to Terminal #5 of Slave unit.

4.  Connect Terminal #16 from the 

Master unit to Terminal #6 on the 

Slave unit.

5.  Connect Terminal #17 from the Master unit to Terminal #7 on the Slave unit.

SLAVE POSITION

(ON)

MASTER POSITION

(OFF)

JUMPER

JUMPER

ON

SLAVE

SLAVE

ON

FIGURE 12

MASTER

SLAVE

15

14

13

12

11

9

8

7

6

5

4

3

2

1

10

16 17 18

15

14

13

12

11

9

8

7

6

5

4

3

2

1

10

16 17 18

TIMER TO CLOSE OPTION

The operator is equipped with a timer to close option for use with control devices, such as a 

radio control or card key control. The 

AUTO RE-CLOSE TIMER

 adjustment screw is located on 

the printed circuit board. The operator is shipped from the factory with this timer preset to 

the OFF position, fully counter-clockwise. As the timer adjustment screw is rotated clockwise, 

the closing of the gate can be delayed from 2 seconds to 60 seconds.

LOCATION OF AUTO CLOSE 

TIMER ADJUSTMENT

2 SEC

OFF

AUTO 

CLOSE 

TIMER

60 SEC

Summary of Contents for rsw





























Reviews: