background image

4

IMPORTANT NOTICE FOR GATE OPERATORS  

MANUFACTURED AFTER JANUARY 11TH, 2016

All gate operators manufactured after January 11th, 2016 must have a 

monitored input for each direction. In order to satisfy this requirement, 

all PowerMaster gate operators with the universal board will have one 

monitored input for each direction.  The close photo (11) terminal will 

function for the close direction and the open photo (10) will function 

for the open direction. These terminals will look for, or “monitor”, the 

presence of a 10k in-line resistor.  If either terminal does not detect the 

presence of the monitored device, the unit will function in constant 

contact for this direction.  

Note:  The first time a monitored device is added to the unit, the board 

must “learn” what the monitored device is.  To have the board learn the 

monitored device, perform the following steps:

1.  With the power off, hold both the open and close limit 

simultaneously.

2.  Power up the unit and release your fingers from the limits. The 

unit has now learned the monitored device.

E.g. The operator detects there is a monitored device on the 11 terminal 

but not the 10 terminal.  The operator will function in momentary 

contact to close and constant pressure to open.

Following are the monitored devices acceptable for use with the 

GSMCB02:

Any actions taken to circumvent this monitoring are in violation of the 

UL325, building code, and local laws.

Device

Manufacturer

Description

Prime-Guard

Miller Edge

Monitored Photoeye

Reflecti-Guard

Miller Edge

Retroreflective Monitored Photoeye

IRB-MON

EMX

Monitored Photoeye

IRB-RET

EMX

Retroreflective Monitored Photoeye

The Solution

Miller Edge

Multiple Safety Devices

Summary of Contents for rsw





























Reviews: