background image

IMPORTANT SAFETY INSTRUCTIONS 

 
Operators must read and understand this manual before operating or 
maintaining this machine. 
Do not operate this machine in flammable or explosive areas. 

This machine is designed solely for scrubbing dirt and dust in an indoor environment. 

PowerBoss

 does not recommend using this machine in any other capacity. 

The following information below may cause a potential hazard to the operator and 
equipment. Read this manual carefully and be aware when these conditions can exist. 
Take necessary steps to locate all safety devices on the machine and train the 
personnel operating the machine. Report any machine damage or faulty operation 
immediately. 

Do not use machine if it is not in proper operating condition.

 

FOR SAFETY DURING OPERATION: 

Keep hands and feet clear of moving parts while machine is in operation. 
Make sure all safety devices are in place and operate properly. All covers, doors and 
latches must be closed and fastened before use. 
During operation, attention should be paid to other persons in the work area and 
especially if small children are present.

 

Electric motors and components can cause an explosion when operated near 
explosive materials or vapor. Do not operate this machine near flammable materials 
such as solvents, thinners, fuels, grain dust, etc.

 

 

Store or park this machine on a level surface only, with parking brake engaged. To 
prevent unauthorized use, machine should be stored or parked with the key removed.

 

This machine is designed for level operation only. 

Do not operate on ramps or 

inclines

This machine is not suitable for picking up hazardous dusts. 
Use caution when moving this machine into areas that are below freezing 
temperatures. Any water in the tanks or hoses can cause damage to the machine. 

FOR SAFETY WHEN SERVICING or MAINTAINING MACHINE: 

Stop on level surface. 
Disconnect the power to the machine by pulling the large red handle (Anderson Plug) 
located in the back of the machine, mid-right, when charging batteries or during 
installation or removal of brushes. 
Avoid moving parts. Do not wear loose jackets, shirts, or sleeves when working on 
machine. 
Avoid contact with battery acid. Battery acid can cause burns. When working on or 
around batteries, wear protective clothing and safety glasses. Remove metal jewelry. 
Do not lay tools or metal objects on top of batteries. 
Charging batteries generates explosive gasses. 

Do not charge batteries when open 

flames or sparks are present. Do not smoke. 

Make sure the charger is turned off 

before disconnecting it from the machine. 
Charge the batteries in a well-ventilated area with the battery cover removed 
completely. 
Do not clean machine with a pressure washer. 
Authorized personnel must perform repairs and maintenance. Use PowerBoss 
supplied replacement parts. 

SAVE THESE INSTRUCTIONS 

 

3

Summary of Contents for CP 2832



















Reviews: