background image

SCRUB DECK 

 

PowerBoss 

offers two deck types (

Cylindrical and Disc

) to fit your specific needs. 

The 

Phoenix 

design is very dynamic wherein the decks are interchangeable in a matter of 

minutes whenever necessary (removal of four bolts, and two quick-connects). The 

cylindrical brush deck

 has five built-in spray jets to uniformly dispense cleaning 

solution on the floor and a wet sweeping debris tray to collect loose objects on the 
floor. 

The disc brush deck 

dispenses cleaning solution through the center hub and 

contained within the bristle area for efficient agitation of cleaning solution to the floor 
and channeled to the rear of the machine. The disc brushes are also easily removed 
and installed with the quick release clamp by using any of the three access doors. 
Another nice feature that these scrub decks have is the ability to have uniform brush 
pressure applied to the floor at all times. Since the scrub deck brush pressure is 
computer controlled, it will automatically adjust and compensate to uneven contours 
on the floor while maintaining brush pressure. 
 
  

CYLINDRICAL SCRUB DECK 





 


 

 

 




Housing 
Spray jets (5) 
Access door (2) 
Nut, Access 
door 
Debris box 
Connector, 
water 
Mounting 
bracket 
Connector, 
power 
Brush motor (2) 
Pulley cover (2) 
Bolt (4) 
Lock washer (4) 
Flat washer (4) 

 

   

  

 

 

 

10

Summary of Contents for CP 2832



















Reviews: