background image

 

This manual is 

for the 

 

POWERBOSS PHOENIX 30/34

 

 

This

 manual

 provides the 

necessary operating and preventive maintenance instructions. Operators must read and 
understand this manual before operating or servicing this machine. 

 

This machine was designed to give you excellent performance and efficiency. For best 
results and minimal cost, please follow the general guidelines below: 
Operate the machine with reasonable care. 
Follow the manufacturers suggested maintenance instructions as provided in this 
booklet. 
Use original PowerBoss supplied parts. 
 

TECHNICAL SPECIFICATIONS 
Model 

    

PHOENIX  

 

 

Model No. 

 

 

 

          PHOENIX 30/34

 

 

 

 

 

 

Current    70 

Amps 

Voltage, Batteries   

 

36 volts, 6-6volt  

Battery 

Capacity 

  275 

AH 

Sound 

Level 

   72dB 

Dimensions (LxWxH) 

 

66” x 44” x 47” (167.64cm x 111.76cm x 119.38cm) 

Gross Weight 

 

 

1,020 lbs (462.66 kg) with batteries 

     614 

lbs 

(278.51 

kg) 

without 

batteries 

Working Grade Transport   

16% (10

°

Working Grade Cleaning   

10% (7

°

Inflate Wheel Pressure to   

50 PSI (Front Wheel)

 

 

Summary of Contents for CP 2832



















Reviews: