Power Electronics SD700 Series, Applications Manual, Page: 52 / 63

SD700
POWER ELECTRONICS
50
OPTIONAL EQUIPMENT
Parameter Name / Description Value
G4: Inputs – S4.1: Digital Inputs.
5 DIGITL IN 1=50
G4.1.5 / Multi-function Digital Input 1
configuration
50

PMP START/STP (Automatic starting of the system).
6 DIGITL IN 2=63
G4.1.6 / Multi-function Digital Input 2
configuration
63  SETPONT PIN1 (low bit configuration for the selection of
multiple setpoints).
7 DIGITL IN 3=64
G4.1.7 / Multi-function Digital Input 3
configuration
64  SETPONT PIN2 (middle bit configuration for the selection of
multiple setpoints).
8 DIGITL IN 4=65
G4.1.8 / Multi-function Digital Input 4
configuration
65

SETPONT PIN3 (high bit configuration for the selection of
multiple setpoints).
G4: Inputs – S4.3: Analogue Input 2.
1 SENSOR 2 ?=S
G4.3.1 / To enable sensor of Analogue
Input 2
Y=YES

Ii allows enabling the sensor of the analogue input 2
that will be used for PID feedback.
2 SENSOR 2=Bar G4.3.2 / Selection of sensor 2 units
Bar

These units must be set according to type of sensor that
user will use in the installation.
3 AIN2 FORMAT=mA G4.3.3 / Analogue Input 2 Format
mA  These units must be set according to the type of sensor that
user will use in the installation.
4 4mA
G4.3.4 / Minimum range of Analogue Input
2
+4mA  These units must be set according to the type of sensor
that user will use in the installation.
5 Smi2=+0.0Bar G4.3.5 / Minimum range of sensor 2
+0.0Bar

This range must be set according to the type of sensor
that user will use in the installation.
620mA
G4.3.6 / Maximum range of Analogue Input
2
+20mA  These units must be set according to the type of sensor
that user will use in the installation.
7 Sma2=+10.0Bar G4.3.7 / Maximum range of sensor 2
+10.0Bar

This range must be set according to the type of
sensor that user will use in the installation.
G25: Pump Control – S25.1: Setpoints.
1 CONTROL MODE=1 G25.1.1 / Control mode 1  Pumps. The drive will start in pump control mode.
5 SETPT1=1.0Bar G25.1.5 / Local setpoint 1 for the PID
1.0Bar  It allows user to set the value of the speed reference 1
for the equipment. (Set according to the requirements of the applic.)
6 SETPT2=2.0Bar G25.1.6 / Local setpoint 2 for the PID
2.0Bar

It allows user to set the value of the speed reference 2
for the equipment. (Set according to the requirements of the applic.)
7 SETPT3=3.0Bar G25.1.7 / Local setpoint 3 for the PID
3.0Bar  It allows user to set the value of the speed reference 3
for the equipment. (Set according to the requirements of the applic.)
8 SETPT4=4.0Bar G25.1.8 / Local setpoint 4 for the PID
4.0Bar  It allows user to set the value of the speed reference 4
for the equipment. (Set according to the requirements of the applic.)
9 SETPT5=5.0Bar G25.1.9 / Local setpoint 5 for the PID
5.0Bar

It allows user to set the value of the speed reference 5
for the equipment. (Set according to the requirements of the applic.)
10 SETPT6=6.0Bar G25.1.10 / Local setpoint 6 for the PID
6.0Bar  It allows user to set the value of the speed reference 6
for the equipment. (Set according to the requirements of the applic.)
11 SETPT7=7.0Bar G25.1.11 / Local setpoint 7 for the PID
7.0Bar  It allows user to set the value of the speed reference 7
for the equipment. (Set according to the requirements of the applic.)
12 SETPT8=8.0Bar G25.1.12 / Local setpoint 8 for the PID
8.0Bar

It allows user to set the value of the speed reference 8
for the equipment. (Set according to the requirements of the applic.)
G25: Pump Control – S25.2: PID Setting.
3 PID FBK=AI2 G25.2.3 / PID feedback source
AI2  It allows selecting Analogue Input 2 as feedback signal for
PID regulator.
G25: Pump Control – S25.3: Start Conditions.
1 LP Pon=0.0Bar G25.3.1 / Wake up level of the drive
x.xBar  When demand decreases, the drive can go in sleep
mode. (It allows setting the wake up level for the drive. This value is
set as units of PID setpoint).
G25: Pump Control – S25.4: Stop Conditions.
1 LP T SLP=20s
G25.4.1 / Delay time before activating sleep
mode
20s  This delay time will be applied to any conditions that
activate the sleep mode. These conditions are: sleep speed, No
Flow input, Flow measurement and sleep current. If anyone of them
is met, the time to activate sleep mode will start elapsing.
2 40.0% G25.4.2 / Sleep speed for local setpoint 1
+40.0%

It allows setting the sleep speed 1 below which the
drive will sleep whenever local setpoint 1 is selected. (Set
according to the installation).
3 42.0% G25.4.3 / Sleep speed for local setpoint 2
+42.0%  It allows setting the sleep speed 2 below which the
drive will sleep whenever local setpoint 2 is selected. (Set
according to the installation).
4 44.0% G25.4.4 / Sleep speed for local setpoint 3
+44.0%

It allows setting the sleep speed 3 below which the
drive will sleep whenever local setpoint 3 is selected. (Set
according to the installation).
5 46.0% G25.4.5 / Sleep speed for local setpoint 4
+46.0%  It allows setting the sleep speed 4 below which the
drive will sleep whenever local setpoint 4 is selected. (Set
according to the installation).
6 SLPsp=+48.0% G25.4.6 / Sleep speed for local setpoint 5
+48.0%  It allows setting the sleep speed 5 below which the
drive will sleep whenever local setpoint 5 is selected. (Set
according to the installation).