manualshive.com logo in svg

Power Craft CDM6180, User Manual & Warranty

Share
Download
Power Craft CDM6180 User Manual & Warranty Download Page 12

UK Helpline 0203-5142281 • Ireland Helpline 1800-719901 

Web Support: www.servotool.eu

Model Number: PAC-18/4K 

 

 

12

performed. Use of the power tool for operations different from intended 
could result in hazardous situation.

h.   Damaged switches must be replaced at a customer service repair centre. 

Do not use power tools that cannot be switched on and off.

i.   Do not leave power tools unattended while they are switched on. Always 

switch off the tool and wait until it has come to a full standstill before 
leaving.

j.   If the mains cable has been damaged, it must be replaced with a spe-

cial mains cable. These can be obtained from the manufacturer or the 
manufacturer’s customer service department. The mains cable may only 
be replaced by the manufacturer, the manufacturer’s customer service 
department or equally qualified persons.

5)  Battery tool use and care

a.   Ensure the switch is in the off position before inserting battery pack. 

Inserting the battery pack into power tools that have the switch on invites 
accidents.

b.  Recharge only with the charger specified by the manufacturer. A charger 

that is suitable for one type of battery pack may create a risk of fire when 
used with another battery pack.

c.   Use power tools only with specifically designated battery packs. Use of 

any other battery packs may create a risk of injury and fire.

d.  When battery pack is not in use, keep it away from other metal objects 

like paper clips, coins, keys, nails, screws, or other small metal objects that 
can make a connection from one terminal to another. Shorting the 
battery terminals together may cause burns of a fire.

e.   Under abusive conditions, liquid may be ejected from the battery; avoid 

contact. If contact accidentally occurs, flush with water. If liquid contacts 
eyes, additionally seek medical help. Liquid ejected from the battery may 
cause irritations or burns.

6)  Service

a.   Please use a qualified expert who uses original replacement parts to repair 

your power tool. This will ensure proper functioning of the power tool.

b.   Caution! The use of any accessories or additional tools other than those 

recommended in this manual may lead to an increased risk of injury. Only 
use original replacement parts.

Safety instructions

CDM6180 Ma-GB-IRE 1108-10.indd   12

8/10/11   10:32:33 AM

Summary of Contents for CDM6180

































Reviews:

No comments

Brands by name

Popular brands

Load more brands