background image

En

glish

3

1 Important

Read and understand all instructions before you 

use your product. If damage is caused by failure 

to follow instructions, the warranty does not 

apply.

Safety

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT 

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS 

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead 

symbol, within an equilateral triangle, is 

intended to alert the user to the presence 

of uninsulated “dangerous voltage” within 

the product’s enclosure that may be of 

sufficient magnitude as to constitute a 

risk of electric shock to persons. 

The exclamation point within an 

equilateral triangle is intended to alert 

the user to the presence of important 

operating and maintenance (servicing) 

instructions in the literature 

accompanying the appliance. 

Risk of electric shock or fire!

•  Before you make or change any 

connections, make sure that all devices are 

disconnected from the power outlet.

•  Never expose the product and accessories to 

rain or water. Never place liquid containers, 

such as vases, near the product. If liquids 

are spilt on or into the product, disconnect it 

from the power outlet immediately. Contact 

Consumer Care to have the product checked 

before use.

•  Never place the product and accessories 

near naked flames or other heat sources, 

including direct sunlight.

•  Never insert objects into the ventilation 

slots or other openings on the product.

•  Where the mains plug or an appliance 

coupler is used as the disconnect device, 

the disconnect device shall remain readily 

operable.

•  Battery (battery pack or batteries 

installed) shall not be exposed to excessive 

heat such as sunshine, fire or the like.

•  Disconnect the product from the power 

outlet before lightning storms. 

•  When you disconnect the power cord, 

always pull the plug, never the cable. 

Risk of short circuit or fire!

•  For identification and supply ratings, see 

the type plate at the back or bottom of the 

product.

•  Before you connect the product to the 

power outlet, ensure that the power 

voltage matches the value printed on 

the back or bottom of the product. Never 

connect the product to the power outlet if 

the voltage is different.

Risk of injury or damage to this product!

•  For wall mounting, this product must 

be securely attached to the wall in 

accordance with the installation 

instructions. Use only the supplied wall 

mount bracket (if available). Improper wall 

mounting may result in accident, injury 

or damage. If you have any query, contact 

Consumer Care in your country.

•  Never place the product or any objects 

on power cords or on other electrical 

equipment. 

•  If the product is transported in 

temperatures below 5°C, unpack the 

product and wait until its temperature 

matches room temperature before 

connecting it to the power outlet. 

•  Parts of this product can be made of 

glass. Handle with care to avoid injury and 

damage.

Summary of Contents for PDB70/00




















Reviews: