manualshive.com logo in svg

Polycom CX5500, Administrator'S Manual

Share
Download
Polycom CX5500 Administrator'S Manual Download Page 288

Polycom CX5500 Unified Conference Station Administrator’s Guide 

1.1.0

 

Polycom, Inc. 

288 

Parameter 

Permitted Values 

Default 

reg.x.outboundProxy.address 

dotted-decimal 
IP address or 
hostname 

Null 

The IP address or hostname of the SIP server to which the phone sends all requests. 

reg.x.outboundProxy.failOver.failBack.mode 

newRequests 
DNSTTL 
registration 
duration 

newRequests 

The mode for failover failback (overrides 

reg.x.server.y.failOver.failBack.mode

).  

newRequests 

all new requests are forwarded first to the primary server regardless of the last used server.  

DNSTTL 

the phone tries the primary server again after a timeout equal to the DNS TTL configured for the server 

that the phone is registered to.  

registration 

the phone tries the primary server again when the registration renewal signaling begins.  

duration 

the phone tries the primary server again after the time specified by 

reg.x.outboundProxy.failOver.failBack.timeout

 expires. 

reg.x.outboundProxy.failOver.failBack.timeout 

0, 60 to 65535 

3600 

The time to wait (in seconds) before failback occurs (overrides 

reg.x.server.y.failOver.failBack.timeout

).If the fail back mode is set to Duration, the phone waits this 

long after connecting to the current working server before selecting the primary server again. If 0, the phone will not 
fail-back until a fail-over event occurs with the current server. 

reg.x.outboundProxy.failOver.failRegistrationOn 

0 or 1 

0 

When set to 1, and the reRegisterOn parameter is enabled, the phone will silently invalidate an existing 
registration (if it exists), at the point of failing over. When set to 0, and the reRegisterOn parameter is 
enabled, existing registrations will remain active. This means that the phone will attempt failback without 
first attempting to register with the primary server to determine if it has recovered.  

Note that 

reg.x.outboundProxy.failOver.RegisterOn

 must be enabled. 

reg.x.outboundProxy.failOver.onlySignalWithRegistered 

0 or 1 

1 

When set to 1, and the reRegisterOn and failRegistrationOn parameters are enabled, no signaling is 
accepted from or sent to a server that has failed until failback is attempted or failover occurs. If the 
phone attempts to send signaling associated with an existing call via an unregistered server (for 
example, to resume or hold a call), the call will end. No SIP messages will be sent to the unregistered 
server. When set to 0, and the reRegisterOn and failRegistrationOn parameters are enabled, signaling 
will be accepted from and sent to a server that has failed (even though failback hasn’t been attempted or 
failover hasn’t occurred). 

reg.x.outboundProxy.failOver.reRegisterOn 

0 or 1 

0 

This parameters overrides 

reg.x.server.y.failOver.failBack.RegisterOn

. When set to 1, the phone will 

attempt to register with (or via, for the outbound proxy scenario), the secondary server. If the registration succeeds 
(a 200 OK response with valid expires), signaling will proceed with the secondary server. When set to 0, the phone 
won’t attempt to register with the secondary server, since the phone will assume that the primary and secondary 
servers share registration information.  

reg.x.outboundProxy.port 

1 to 65535 

0 

The port of the SIP server to which the phone sends all requests. 

Summary of Contents for CX5500



































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands