Polycom CX5500 Page 353 Administrator'S Manual Download

Page: 353 / 386

Polycom CX5500 Unified Conference Station Administrator’s Guide

1.1.0

Polycom, Inc.

353

Note: Reading the Following Tables

In the following table, a

Yes

in the Supported column means the header is sent and properly parsed.

The phone may not actually generate the response.

1xx Responses - Provisional

Supported 1xx SIP Responses

Response

Supported

100 Trying

Yes

180 Ringing

Yes

181 Call Is Being Forwarded

182 Queued

183 Session Progress

Yes

2xx Responses - Success

Supported 2xx SIP Responses

Response

Supported

Notes

200 OK

Yes

202 Accepted

Yes

In REFER transfer.

3xx Responses - Redirection

Supported 3xx SIP Responses

Response

Supported

300 Multiple Choices

Yes

301 Moved Permanently

Yes

Summary of Contents for CX5500



































































































































































































































































































































































































Search results

Summary of Contents for CX5500

Reviews:

Related manuals for CX5500

Brands by name

Popular brands

Polycom CX5500, Administrator'S Manual

Search results

Summary of Contents for CX5500

Reviews:

Related manuals for CX5500

Brands by name

Popular brands