Polycom CX5500 Page 215 Administrator'S Manual Download | Manualshive

Page: 215 / 386

background image

Polycom CX5500 Unified Conference Station Administrator’s Guide

1.1.0

Polycom, Inc.

215

The phone displays a

Config file error

message for 5-seconds after it boots up (see the following figure)

Pre-UC Software 3.3.0 configuration files are being used with UC Software 3.3.0. Specifically, the following
parameters are in the configuration files:



one.chord.ringer.x.freq.1



se.pat.callProg.x.name



ind.anim.IP_500.x.frame.x. duration



ind.pattern.1.step.x.state



feature.2.name



feature.9.name

Also the configuration files contain:



more

than 100 “unknown” parameters



more than 100 “out-of-range” parameters



more than 100 “invalid” parameters

Correct the configuration files, remove the invalid parameters, and restart the phone.

When you are upgrading phone software using the Web Configuration Utility, the phone is unable to
connect to the Polycom Hosted Server.

Occasionally, the phone is unable to connect to the Polycom Hosted Server because:



The Polycom Hosted Server is temporarily unavailable.



There isn’t any software upgrade information for the phone to receive.



The network configuration is preventing the phone from connecting to the Polycom Hosted Server.

Note: UC Software 4.0.0 does not support internet access for software upgrades through a Web proxy

.

To troubleshoot the issue:



Try upgrading your phone later.



Verify that new software is available for your phone. To check, see the

Polycom UC Software/Polycom SIP

Software Release Matrix

.



Veri

fy that your network’s configuration will allow the phone to connect to http://downloads.polycom.com.

If the issue persists, try manually upgrading your phone’s software. To upgrade phone software using this method,
see

Set Up the Provisioning Server

.

«
...
213
214
215
216
217
...
»

Summary of Contents for CX5500



































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX5500

Brand: E-Mu Pages: 72

Brand: E-Mu Pages: 44

Brand: AeroAudio Pages: 8

Brand: Brähler Systems Pages: 25

Brand: Discount Car Stereo Pages: 5

Brand: Onn Pages: 11

PARTNER II Release 4.1

Brand: Lucent Technologies Pages: 363

Brand: hotset Pages: 2

Brand: Subpac Pages: 15

Brand: Polycom Pages: 10

Brand: Ruida Technology Pages: 35

Brand: Alpine Pages: 16

Brand: ClearOne Pages: 48

Brand: btsr Pages: 71

Brand: Raven Pages: 48

L-force PROFINET E94AYCER

Brand: Lenze Pages: 114

Brand: Sharp Pages: 20

Brand: ELBE Pages: 97

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands