Polaris Light Utility Hauler 6x6 Owner'S Manual Download

Page: 88 / 116

MAINTENANCE AND LUBRICATION

Adjustments

Rear Axle Drive Chain Adjustment

All procedures used in adjusting the front chain apply to the rear chain

adjustment. Total slack for the rear chain, however, should be adjusted

to 1/4

″

-1/2

″

(.6-1.3 cm).

Carburetor/Engine Idle RPM Adjustment

Recommended engine idle RPM is 1200 +/- 200. If the engine idle

speed is unsatisfactory and all other conditions are favorable, the

carburetor can be adjusted as follows:
1. Start the engine and allow it to warm up for

approximately five minutes.

2. Place the transmission in gear with the

parking brake applied.

3. Adjust the carburetor idle screw (1) in or

out until the desired idle RPM is reached.

Turning the screw in (clockwise) will raise

RPM. Turning the screw out

(counterclockwise) will lower RPM.

1/4

″

-1/2

″

(.6-1.3 cm)

3/16

″

-3/8

″

(.48 cm - .95 cm)

Summary of Contents for Light Utility Hauler 6x6





















































































































Search results

Summary of Contents for Light Utility Hauler 6x6

Reviews:

Related manuals for Light Utility Hauler 6x6

Brands by name

Popular brands

Polaris Light Utility Hauler 6x6, Owner'S Manual

Search results

Summary of Contents for Light Utility Hauler 6x6

Reviews:

Related manuals for Light Utility Hauler 6x6

Brands by name

Popular brands