Polaris Light Utility Hauler 6x6 Owner'S Manual Download

Page: 21 / 116

SAFETY

Operator Safety

POTENTIAL HAZARD
Operating the LUH 6x6 at excessive speeds.
WHAT CAN HAPPEN
Excessive speed increases the operator’s chance of losing

control of the vehicle, which can result in an accident.
HOW TO AVOID THE HAZARD
Always operate the vehicle at a speed that’s proper for the

terrain, visibility and operating conditions, and your experience.

POTENTIAL HAZARD
Improperly operating in reverse.
WHAT CAN HAPPEN
The LUH 6x6 could collide with an obstacle or person,

resulting in severe injury.
HOW TO AVOID THE HAZARD
Before shifting into reverse gear, always check for obstacles or

people behind the vehicle. When it’s safe to proceed, back

slowly.

WARNING

Summary of Contents for Light Utility Hauler 6x6





















































































































Search results

Summary of Contents for Light Utility Hauler 6x6

Reviews:

Related manuals for Light Utility Hauler 6x6

Brands by name

Popular brands

Polaris Light Utility Hauler 6x6, Owner'S Manual

Search results

Summary of Contents for Light Utility Hauler 6x6

Reviews:

Related manuals for Light Utility Hauler 6x6

Brands by name

Popular brands