Polaris Light Utility Hauler 6x6 Owner'S Manual Download

Page: 113 / 116

111

WARRANTY

This warranty does not cover the use of unauthorized lubricants,

chemicals, or fuels that are not compatible with the vehicle. The

exclusive remedy for breach of this warranty shall be, at Polaris’

exclusive option, repair or replacement of any defective materials, or

components or products. THE REMEDIES SET FORTH IN THIS

WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY

PERSON FOR BREACH OF THIS WARRANTY. POLARIS SHALL

HAVE NO LIABILITY TO ANY PERSON FOR INCIDENTAL,

CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY

DESCRIPTION, WHETHER ARISING OUT OF EXPRESS OR

IMPLIED

WARRANTY OR ANY OTHER CONTRACT, NEGLIGENCE, OR

OTHER TORT OR OTHERWISE. Some states do not permit the

exclusion or limitation of incidental or consequential damages or

implied warranties, so the above limitations or exclusions may not

apply to you if inconsistent with controlling state law.

ALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED

TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN

DURATION TO THE ABOVE SIX MONTH WARRANTY PERIOD.

POLARIS FURTHER DISCLAIMS ALL EXPRESS WARRANTIES

NOT STATED IN THIS WARRANTY. Some states do not allow

limitations on how long an implied warranty lasts, so the above

limitation may not apply to you if inconsistent with controlling state

law.

HOW TO OBTAIN WARRANTY SERVICE

If your vehicle requires warranty service, you must take it to a Polaris

Servicing Dealer. When requesting warranty service you must present

your copy of the Warranty Registration form to the dealer. (THE

COST OF TRANSPORTATION TO AND FROM THE DEALER IS

YOUR RESPONSIBILITY). Polaris suggests that you use your

original selling dealer; however, you may use any Polaris Servicing

Dealer to perform warranty service.

Please work with your dealer to resolve any warranty issues. Should

your dealer require any additional assistance they will contact the

appropriate person at Polaris.

This warranty gives you specific legal rights, and you may also have

other rights which vary from state to state.

If any of the above terms are void because of state or federal law, all

other warranty terms will remain in effect.

Engine Oil

1. Mixing oil brands or using non-recommended oil may cause engine

damage. We recommend the use of Polaris engine oil.

2. Damage resulting from the use of non-recommended lubricants may

not be covered by warranty.

Summary of Contents for Light Utility Hauler 6x6





















































































































Search results

Summary of Contents for Light Utility Hauler 6x6

Reviews:

Related manuals for Light Utility Hauler 6x6

Brands by name

Popular brands

Polaris Light Utility Hauler 6x6, Owner'S Manual

Search results

Summary of Contents for Light Utility Hauler 6x6

Reviews:

Related manuals for Light Utility Hauler 6x6

Brands by name

Popular brands