Polaris Light Utility Hauler 6x6 Owner'S Manual Download

Page: 28 / 116

SAFETY

Operator Safety

POTENTIAL HAZARD
Improperly crossing or turning on hills.
WHAT CAN HAPPEN
Improperly crossing or turning as hills could cause loss of control

or overturn.
HOW TO AVOID THE HAZARD
Never attempt to turn the LUH 6x6 around on any hill until you’ve

mastered the turning technique (on level ground) as described in

the owner’s manual. See page 57. Use extra caution when

turning on any hill.
Avoid crossing the side of a steep hill. If it’s unavoidable, always

follow proper procedures as described in the owner’s manual.
Avoid hills with excessively slippery or loose surfaces.
Shift your weight to the uphill side of the vehicle.

WARNING

Summary of Contents for Light Utility Hauler 6x6





















































































































Search results

Summary of Contents for Light Utility Hauler 6x6

Reviews:

Related manuals for Light Utility Hauler 6x6

Brands by name

Popular brands

Polaris Light Utility Hauler 6x6, Owner'S Manual

Search results

Summary of Contents for Light Utility Hauler 6x6

Reviews:

Related manuals for Light Utility Hauler 6x6

Brands by name

Popular brands