background image

6

7

EN

 – Installation and operation guide SIMPLE MOVE 102

EN

 – Installation and operation guide SIMPLE MOVE 102

EN

EN

Do not use adhesives to mount the drive unit.

 

WARNING

Manual unlocking may result in uncontrolled movement of the gate.
Place the sticker indicating the manual unlocking mechanism near the component 

used for quick start-up.

IMPORTANT

Install 

fi

 xed control devices at a height of at least 1.5 m and within sight of the gate 

but away from moving parts.

A

 er installation, make sure that:

•  the mechanism is properly adjusted;
•  the manual unlocking mechanism works correctly;
•   the drive unit reverses operation direction when the gate encounters a 50-mm 

obstacle that is halfway up the gate leaf.

 

WARNING

For gate operation in automatic mode or if the control device is out of sight, photocells 

must be installed. 
The automatic drive unit must operate in at least one direction with no intentional 

activation by the user.

For gate operation in automatic mode or if the gate opens onto a public road, installation 

of an orange light may be required in accordance with the regulations in the country, 

where the drive unit is installed.

6. Clothing recommendations

Take o

  any jewellery (a bracelet, chain, etc.) during assembly. 

When executing any activities as well as drilling and welding operations, wear 

appropriate protection (special protective glasses, gloves, ear protectors, etc.).

7.  Safety instructions regarding operation

 

WARNING

This drive unit may be used by children aged 8 and over and by persons, whose 

physical, sensory or mental capacity is impaired, or persons with no experience or 

knowledge, as long as they are under proper supervision or have received proper 

instructions on the safe use of the equipment and have been informed about possible 

hazards. Children should not play with the drive unit. Children are not allowed to 

perform cleaning and maintenance works, for which the user is responsible.

The sound pressure level of the drive unit is less than or equal to 70 dB (A). The noise 

emitted by the structure, to which the drive unit will be connected, is not taken into 

account.

 

WARNING

Every potential user must be informed by the installation engineer about the rules of using 

the drive unit in accordance with all the recommendations of this guide. It is essential to 

make sure that no untrained people can open the gate. The user must monitor the gate 

opening or closing and keep all people at a safe distance until the operation is complete. 

Never allow children to play with the gate control devices.
Keep remote controls out of the reach of children.
Do not deliberately prevent the gate from moving.

In the event of a malfunction, disconnect the power, use the emergency unlocking to 

gain access to the property and contact the POLARGOS technical support department.
Do not try to open the gate manually if the drive unit has not been unlocked. No natural 

obstacles (a branch, a stone, tall grass, etc.) should obstruct the movement of the gate.

8.   Safety instructions regarding maintenance

 

DANGER

The drive unit must be disconnected from any power supply during cleaning and 

maintenance as well as replacement of the parts.

 

WARNING

Every month, the following must be checked:
-  the installation, in order to discover any signs of wear or damage to the conductors 

or assembly elements.

-  whether the drive unit changes operation direction, when the gate encounters a 50-mm 

obstacle that is halfway up the gate leaf.

Do not use the drive unit if it needs repairing or adjusting. Gates in poor condition must 

be repaired, reinforced or even replaced a

 er prior approval of the POLARGOS technical 

department.
Use only original parts for any maintenance or repair work. Any technical, electronic, 

or mechanical modi

fi

 cations to the drive unit must be performed with the approval 

of the POLARGOS assistance department.

If the installation is equipped with photocells and/or an orange light, clean the 

photocells optical components and the orange light regularly.

Summary of Contents for SIMPLE MOVE 102


























Reviews: