Polar Air SWC-04-ECM Installation, Operating & Service Manual Download Page 39

Page: 39 / 55

Page 37 of 52

PG2021_SWC-V-ECM_02

Filter Switch (S6

PCB)

Green LED blinks 7
times, stops for 3s

Filter switch is

opened.

2. replace the new filter

Electric Heater

failure

Green LED blinks 8
times, stops for 3s

Only for unit with

EH.

1. Change fan speed to high.

EH safety switch is

opened.

2. Replace the damaged EH safety
switch.

EC motor

failure(CN4)

Green LED blinks 9

times, stops 3s

No EC motor

feedback

1. Check Modbus setting.

2. Check the EC motor.

EC motor

failure(CN5)

Green LED blinks 10

times, stops 3s

E10

No EC motor

feedback

1. Check Modbus setting.

2. Check the EC motor.

Anti-frozen

protection

Green LED blinks 12

times, stops for 3s

E12

When unit is

standby, Tr<2

ºC

1. Turn on unit to keep Tr high than 5ºC

Indoor coil sensor 3

failure (S6 PCB)

Green LED blinks 13

times, stops for 3s

E13

Ti3 sensor

unplugged or

damaged.

1. Check if Ti3 plug is connected or not.

2. Check if sensor’s resistance is correct
or not.

Indoor coil sensor 4

failure (S6 PCB)

Green LED blinks 14

times, stops for 3s

E14

Ti4 sensor

unplugged or

damaged.

1. Check if Ti4 plug is connected or not.

2. Check if sensor’s resistance is correct
or not.

PM2.5 sensor failure

(S6 PCB)

Green LED blinks 15

times, stops for 3s

E15

PM2.5 sensor

unplugged or

damaged.

1. Check if PM2.5 plug is connected or
not.

2. Check if sensor’s resistance is correct
or not.

AQI sensor failure

(S6 PCB)

Green LED blinks 16

times, stops for 3s

E16

AQI sensor

unplugged or

damaged.

1. Check if AQI plug is connected or not.

2. Check if sensor’s resistance is correct
or not.

Cooke Industries - Phone: +64 9 579 2185 Email: [email protected] Web: www.cookeindustries.co.nz

Summary of Contents for SWC-04-ECM
























































Search results

Summary of Contents for SWC-04-ECM

Reviews:

Related manuals for SWC-04-ECM

Brands by name

Popular brands

Polar Air SWC-04-ECM, Installation, Operating & Service Manual

Search results

Summary of Contents for SWC-04-ECM

Reviews:

Related manuals for SWC-04-ECM

Brands by name

Popular brands