Polar Air SWC-04-ECM Installation, Operating & Service Manual Download Page 38

Page: 38 / 55

Page 36 of 52

PG2021_SWC-V-ECM_02

LED Display and Error Description

Power / Operation LED light (both green)

Unit on

Power LED Off, Operation LED On

Unit in standby

Power LED On, Operation LED Off

For all units - Green LED

Error Description

Blink

LED display

Reason

Remedy

Return air sensor

failure

Green LED blinks 1
times, stops for 3s

Room sensor

unplugged or

damaged.

1. Check if Tr plug is connected or not.

2. Check if sensor’s resistance is correct
or not.

Indoor coil sensor 1

failure

Green LED blinks 2
times, stops for 3s

Ti1 sensor

unplugged or

damaged.

1. Check if Ti1 plug is connected or not.

2. Check if sensor’s resistance is correct
or not.

Indoor coil sensor 2

failure

Green LED blinks 3
times, stops for 3s

Ti2 sensor

unplugged or

damaged.

1. Check if Ti2 plug is connected or not.

2. Check if sensor’s resistance is correct
or not.

Water pump failure

Green LED blinks 4
times, stops for 3s

Float switch is

opened.

1. Check if the condensate water pipe is
connected or not.

2. Check if the pump is functioning or
not.

Indoor coil low

temperature

protection

Green LED blinks 5
times, stops for 3s

Water temperature

is lower than 3 ºC.

Check the water temperature.

Indoor coil overheat

protection

Green LED blinks 6
times, stops for 3s

Water temperature

is higher than 70

ºC.

Check the water temperature

1. Check if filter block or not

Cooke Industries - Phone: +64 9 579 2185 Email: [email protected] Web: www.cookeindustries.co.nz

Summary of Contents for SWC-04-ECM
























































Search results

Summary of Contents for SWC-04-ECM

Reviews:

Related manuals for SWC-04-ECM

Brands by name

Popular brands

Polar Air SWC-04-ECM, Installation, Operating & Service Manual

Search results

Summary of Contents for SWC-04-ECM

Reviews:

Related manuals for SWC-04-ECM

Brands by name

Popular brands