PlayNation Play Systems 2500-1 Assembly Instructions Manual Download

Page: 74 / 87

INTO THE GROOVE OF THE ROOF PEAK.

THE TOP HOLES ONLY "1".

FIRST ROOF BOARD

ROOF

THEN INSTALL 1-1/2" WOOD SCREWS IN

PLACE THE TONGUE OF THIS BOARD

SCREWS IN THE TOP HOLES ONLY "2".

BOARD THEN INSTALL 1-1/2" WOOD

PEAK

SECOND ROOF BOARD
PLACE THE TONGUE OF THIS BOARD
INTO THE GROOVE OF THE FIRST ROOF

THIRD
ROOF BOARD

1 X 5 X 54-1/4"
ROOF BOARD
(7 PER SIDE)

NOW GO BACK AND
INSTALL 1-1/2" WOOD SCREWS IN THE
BOTTOM HOLES OF THE FIRST ROOF
BOARD HERE "3".

STEP 36: ROOF BOARDS

DUE TO MILLING VARIATIONS IT MIGHT BE EASIEST TO INSTALL THE ROOF BOARDS AS DESCRIBED

BELOW.

1: FIRST PLACE THE TONGUE OF THE FIRST ROOF BOARD INTO THE GROOVE OF THE ROOF PEAK.

NOW SECURE THE TOP HOLES OF THE FIRST ROOF BOARD TO THE ROOF SUPPORTS WITH #8 X 1-

1/2" WOOD SCREWS.

2: SECOND PLACE THE TONGUE OF THE SECOND ROOF BOARD INTO THE GROOVE OF THE

FIRST ROOF BOARD. NOW SECURE THE TOP HOLES OF THE SECOND ROOF BOARD TO THE

ROOF SUPPORTS WITH #8 X 1-1/2" WOOD SCREWS.

3: THIRD GO BACK AND SECURE THE BOTTOM HOLES OF THE FIRST ROOF BOARD TO THE ROOF

SUPPORTS.

4: NOW PLACE THE TONGUE OF THE THIRD ROOF BOARD INTO THE GROOVE OF THE SECOND

ROOF BOARD. SECURE THE TOP HOLES OF THE THIRD ROOF BOARD TO THE ROOF SUPPORTS

WITH #8 X 1-1/2" WOOD SCREWS.

5: GO BACK AND SECURE THE BOTTOM HOLES OF THE SECOND ROOF BOARD TO THE ROOF

SUPPORTS.

6: REPEAT THIS PROCESS FOR THE REST OF THE ROOF BOARDS ON EACH SIDE OF THE ROOF.

THERE ARE SEVEN 1 X 5 X 54-1/4" ROOF BOARDS ON EACH SIDE OF THE ROOF.

Summary of Contents for 2500-1
























































































Search results

Summary of Contents for 2500-1

Reviews:

Related manuals for 2500-1

Brands by name

Popular brands

PlayNation Play Systems 2500-1, Assembly Instructions Manual

Search results

Summary of Contents for 2500-1

Reviews:

Related manuals for 2500-1

Brands by name

Popular brands