PlayNation Play Systems 2500-1 Assembly Instructions Manual Download

Page: 70 / 87

STEP 32: TIC TAC TOE ASSEMBLY

1: LOCATE THE TIC TAC TOE BOX. FIND THE GREEN BRACKETS INSIDE AND THE SCREWS.

2: LOCATE THE 5/4 X 3 X 17-1/2" TIC TAC TOE MOUNT BOARDS.

3: CENTER THE GREEN BRACKETS ON THE TIC TAC TOE BOARDS AND KEEP THE LIP OF THE GREEN

BRACKET AS FLUSH TO THE SIDE OF THE BOARD AS YOU CAN. ATTACH THE GREEN BRACKET TO

THE BOARD WITH THE SHORTEST SCREWS PROVIDED IN THE TIC TAC TOE BOX.

4: NOW ASSEMBLE THE TIC TAC TOE ACCORDING TO THE INSTRUCTIONS IN THE BOX.

IGNORE STEPS 6 AND 7 IN THE INSTRUCTIONS.

MOUNT

TIC TAC TOE

5/4 X 3 X 17-1/2"

BOARD AS YOU CAN.

MOUNT

FLUSH TO THE SIDE OF THE

KEEP LIP OF BRACKET AS

5/4 X 3 X 17-1/2"

TIC TAC TOE

GREEN BRACKET

KEEP LIP OF BRACKET AS

FLUSH TO THE SIDE OF THE

BOARD AS YOU CAN.

Summary of Contents for 2500-1
























































































Search results

Summary of Contents for 2500-1

Reviews:

Related manuals for 2500-1

Brands by name

Popular brands

PlayNation Play Systems 2500-1, Assembly Instructions Manual

Search results

Summary of Contents for 2500-1

Reviews:

Related manuals for 2500-1

Brands by name

Popular brands