PlayNation Play Systems 2500-1 Assembly Instructions Manual Download

Page: 65 / 87

STEP 27: ROOF SUPPORT ASSEMBLIES

1: LAY THE 2 X 4 X 36-3/8" ROOF SUPPORT LEFT AND THE 2 X 4 X 36-3/8" ROOF SUPPORT RIGHT

ON A FLAT SURFACE WITH THE COUNTERBORES FACING THE FLAT SURFACE. ALIGN THE TIPS OF

THE BOARDS AND USE A CARPENTER'S SQUARE TO SQUARE THE BOARDS UP.

2: PLACE THE 5/4 X 6 X 10" ROOF PEAK SUPPORT ON TOP OF THE ROOF SUPPORTS. ALIGN THE

TOP EDGES OF THE ROOF PEAK SUPPORT FLUSH OR SLIGHTLY LOWER THAN THE TOP EDGES OF

THE ROOF SUPPORT LEFT AND RIGHT PIECES.

3: FASTEN ONE SIDE OF THE ROOF PEAK SUPPORT TO ONE OF THE ROOF SUPPORTS WITH TWO

#8 X 2" WOOD SCREWS. USE THE CARPENTER'S SQUARE TO CHECK THE BOARDS ARE SQUARE.

THEN FASTEN THE OTHER ROOF SUPPORT TO THE ROOF PEAK SUPPORT WITH TWO #8 X 2"

WOOD SCREWS.

4: REPEAT SUBSTEPS 1 THROUGH 3 TO CONSTRUCT ONE MORE ROOF SUPPORT ASSEMBLY.

STICK OUT BEYOND THIS SURFACE.

ROOF PEAK SUPPORT CANNOT

ROOF PEAK SUPPORT

ROOF SUPPORT RIGHT

2 X 4 X 36-3/8"
ROOF SUPPORT LEFT

5/4 X 6 X 10"

ALONG THIS SURFACE. THE

WOOD SCREW

#8 X 2"

SQUARE

2 X 4 X 36-3/8"

CARPENTER'S

MAKE THE EDGES OF THE ROOF PEAK SUPPORT
FLUSH OR SLIGHTLY INSIDE THE EDGE OF THE ROOF SUPPORTS.

ROOF BOARDS WILL ATTACH

COUNTERBORES ON THE OTHER SIDE OF THE BOARD FACE THE FLAT SURFACE YOU ARE WORKING ON.

Summary of Contents for 2500-1
























































































Search results

Summary of Contents for 2500-1

Reviews:

Related manuals for 2500-1

Brands by name

Popular brands

PlayNation Play Systems 2500-1, Assembly Instructions Manual

Search results

Summary of Contents for 2500-1

Reviews:

Related manuals for 2500-1

Brands by name

Popular brands