PlayNation Play Systems 2500-1 Assembly Instructions Manual Download

Page: 49 / 87

STEP 11: ATTACHING THE ARCH ROCK WALL SIDE SUPPORTS

1: MOUNT THE ARCH ROCK WALL SIDE SUPPORT ON TOP OF THE ROCK WALL SUPPORT, MAKE SURE THAT THE

TOP END OF THE ARCH ROCK WALL SIDE SUPPORT IS FLUSH WITH THE CORNER POST.

2: FIRST FASTEN THE 3" WOOD SCREW INTO THE ARCH ROCK WALL SIDE SUPPORT TOP HOLE INTO THE ROCK WALL

SUPPORT, MAKE SURE THAT THIS BOARD IS ALIGNED WITH THE ROCK WALL SUPPORT. SECOND FASTEN THE

3" WOOD SCREW INTO THE ARCH ROCK WALL SIDE SUPPORT BOTTOM HOLE TO THE ROCK WALL SUPPORT.

3: THIRD FASTEN THE 3" WOOD SCREW INTO THE ROCK WALL SUPPORT TO THE ARCH ROCK WALL SUPPORT,

MAKE SURE BOTH BOARDS ARE TIGHT TOGETHER.

3" WOOD SCREW

THIRD

TIP FLUSH TO POST

SIDE SUPPORT

3" WOOD SCREW

SECOND

FIRST

3" WOOD SCREW

2 X 6 X 54"

ARCH ROCK WALL

SIDES FLUSH

Summary of Contents for 2500-1
























































































Search results

Summary of Contents for 2500-1

Reviews:

Related manuals for 2500-1

Brands by name

Popular brands

PlayNation Play Systems 2500-1, Assembly Instructions Manual

Search results

Summary of Contents for 2500-1

Reviews:

Related manuals for 2500-1

Brands by name

Popular brands