PlayNation Play Systems 2500-1 Assembly Instructions Manual Download

Page: 39 / 87

LOCATIONS.

3 X 3 X 96"

CORNER POST #1

CORNER POST #4

AT THESE

CORNER POST #3

CORNER POST

CORNER POST #2

LEFT SIDE POSTS WILL

HAVE EXTRA HOLES

REAR CORNER

POST WILL

HAVE AN

EXTRA HOLE AT

THIS

LOCATION.

FRONT OF PLAY SET

STEP 1: CORNER POST LAYOUT

1: THIS STEP IS CRITICAL TO BUILDING THE FORT PROPERLY. IF ANY MISTAKES ARE MADE HERE, YOU WILL NEED TO

DIS-ASSEMBLE AND THE RE-ASSEMBLE TO MAKE YOUR CORRECTIONS.

2: LAY OUT EACH OF THE 3 X 3 X 96" CORNER POSTS IN THE AREA YOU INTEND ON BUILDING THE FORT SIDE OF THE

PLAYSET.

3: USE THE DIAGRAM BELOW TO CORRECTLY IDENTIFY AND ORIENT THE NECESSARY DIRECTION THE POSTS

SHOULD FACE.

NOTE: THE LADDER SIDE IS CONSIDERED THE FRONT OF THE PLAYSET WITH THE SWINGBEAM EXTENDING OFF TO

THE LEFT SIDE.

Summary of Contents for 2500-1
























































































Search results

Summary of Contents for 2500-1

Reviews:

Related manuals for 2500-1

Brands by name

Popular brands

PlayNation Play Systems 2500-1, Assembly Instructions Manual

Search results

Summary of Contents for 2500-1

Reviews:

Related manuals for 2500-1

Brands by name

Popular brands