Planet Networking & Communication WRT-414 Page 82 User Manual Download

Page: 82 / 93

Chapter 8 Tools

This page includes the basic configuration tools, such as Configuration Tools (save or restore

configuration settings), Firmware Upgrade (upgrade system firmware) and Reset.

8.1 Configuration

Tools

- 76 -

The Configuration Tools screen allows you to “Backup” the router’s current configuration setting.

Saving the configuration settings provides an added protection and convenience when problems occur

and you have to reset to factory default. With the saved file, you can re-load the saved configuration

into the router through the “Restore”

function.

If extreme problems occur you can use the “Restore to

Factory Defaults” selection, this will set all configurations to its original default settings.

Summary of Contents for WRT-414






























































































Search results

Summary of Contents for WRT-414

Reviews:

Related manuals for WRT-414

Brands by name

Popular brands

Planet Networking & Communication WRT-414, User Manual

Search results

Summary of Contents for WRT-414

Reviews:

Related manuals for WRT-414

Brands by name

Popular brands