Planet Networking & Communication WRT-414 Page 37 User Manual Download

Page: 37 / 93

5.2.8 DDNS

DDNS allows you to map the static domain name to a dynamic IP address. You must get an account,

password and your static domain name from the DDNS service providers. This router supports

DynDNS and TZO.

Parameters

Description

Dynamic DNS

Enable/Disable the DDNS function of this router.

Provider Select a DDNS service provider. The default setting is “DynDNS”.

Domain name

Your static domain name that use DDNS.

Account / E-mail

The account that your DDNS service provider assigned to you.

Password / Key

The password you set for the DDNS service account above.

After configuration complete, please click “Apply”

button to save the configuration. Then you will see a

screen to prompt you the settings are save successfully. You may press “Continue” for configure other

settings or “Apply” to restart WRT-414 with new configuration.

5.3 LAN

- 31 -

The LAN Port screen below allows you to specify a private IP address for your router’s LAN interface.

Summary of Contents for WRT-414






























































































Search results

Summary of Contents for WRT-414

Reviews:

Related manuals for WRT-414

Brands by name

Popular brands

Planet Networking & Communication WRT-414, User Manual

Search results

Summary of Contents for WRT-414

Reviews:

Related manuals for WRT-414

Brands by name

Popular brands