manualshive.com logo in svg

Planet Networking & Communication WRT-414, User Manual

Share
Download
Planet Networking & Communication WRT-414 User Manual Download Page 57

 

5.6.5 ALG 

Settings 

You can select applications that need “Application Layer Gateway” to support. 

 

 

Parameters 

Description 

Enable 

You can select to enable “Application Layer Gateway” of an application and 

then the router will let that application correctly pass though the NAT 

gateway. 

After configuration complete, please click “Apply”

 

button to save the configuration. Then you will see a 

screen to prompt you the settings are save successfully. You may press “Continue” for configure other 

settings or “Apply” to restart WRT-414 with new configuration. 

 

5.7 Firewall 

- 51 -

 

WRT-414 provides extensive firewall protection by restricting connection parameters, thus limiting the 

risk of hacker attack, and defending against a wide array of common Internet attacks. However, for 

applications that require unrestricted access to the Internet, you can configure a specific client/server 

in a Demilitarized Zone (DMZ). 

Summary of Contents for WRT-414






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands