background image

 

5.6.1 Port 

Forwarding 

The Port Forwarding allows you to re-direct a particular range of service port numbers (from the 

Internet/WAN Ports) to a particular LAN IP address. It helps you to host some servers behind the 

firewall. 

 

 

- 45 -

 

Parameters 

Description 

Enable Port Forwarding 

Enable Port Forwarding. 

Private IP 

This is the private IP of the server in LAN. 

Note: 

You need to give your LAN PC clients a fixed/static IP address for Port 

Forwarding to work properly. 

Type 

This is the protocol type to be forwarded. You can choose to forward “TCP”

or “UDP” packets only or select “both” to forward both “TCP” and “UDP”

packets. 

Port Range 

The range of ports to be forward to the private IP. 

Comment 

The description of this setting. 

Add 

Fill in the "Private IP", “Type”, “Port Range” and "Comment" of the setting to 

be added and then click "Add". Then this Port Forwarding setting will be 

added into the "Current Port Forwarding Table" below. If you find any typo 

before adding it and want to retype again, just click "Clear" and the fields will 

be cleared. 

Reset 

Click “Reset” will clear your current settings to allows you to enter again. 

Summary of Contents for WRT-414






























































































Reviews: