Planet Networking & Communication WRT-414 Page 50 User Manual Download

Page: 50 / 93

Network Address Translation (NAT) allows multiple users at your local site to access the Internet via a

single legal IP Address. NAT provides Firewall protection from hacker attacks and has the flexibility to

allow you to map Private IP Addresses to Public IP Addresses for key services such as Websites and

FTP. If NAT is disabled, all LAN side workstations must have legal IP addresses for Internet access. If

the router is used for routing application, not f

or Internet acce

ss, the NAT function can be disabled.

Parameters

Description

Enable/Disable

You can select to enable or disable the NAT function. After selected, please

click “Apply” to make the settings effect.

- 44 -

After configuration complete, please click “Apply”

button to save the configuration. Then you will see a

screen to prompt you the settings are save successfully. You may press “Continue” for configure other

settings or “Apply” to restart WRT-414 with new configuration.

Summary of Contents for WRT-414






























































































Search results

Summary of Contents for WRT-414

Reviews:

Related manuals for WRT-414

Brands by name

Popular brands

Planet Networking & Communication WRT-414, User Manual

Search results

Summary of Contents for WRT-414

Reviews:

Related manuals for WRT-414

Brands by name

Popular brands