background image

  19 

  

  

Conf

orm

ity

Declaration of Conformity

Manufacturer's Name:

Planar Systems, Inc.

Manufacturer's Address:

1195 NW Compton Drive 
Beaverton, OR 97006 

declares that the products

Model Numbers:

c50RP/c67RP, c50RX/c67RX (DLP projection display)

conforms with the provisions of:

Council Directive 89/336/EEC and amended by 92/31/EEC and 93/68/EEC on Electromagnetic Compatibility;

EN55022:1998 Radiated and Conducted Emissions from IT Equipment

EN55024:1998 Immunity of IT Equipment

Including:

EN61000-4-2

Electrostatic Discharge

EN61000-4-3

Radiated Immunity

EN61000-4-4

Electrical Fast Transients

EN61000-4-5

Line Surge

EN61000-4-6

RF Conducted Susceptibility

EN61000-4-8

Magnetic Field Immunity

EN61000-4-11

Voltage Dips and Interrupts

And: 

EN61000-3-2

Harmonic Current Emissions

EN61000-3-3

Voltage fluctuations and Flicker 

Council Directive 73/23/EEC and amended by M1 and C1 on Low Voltage Equipment Safety:

EN60950:2001 Safety of IT Equipment

The Technical Construction File required by this Directive is maintained at the corporate headquarters of Planar Systems, Inc., 1195 NW Compton Drive, Beaverton, 
OR 97006.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, 
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio 
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the 
interference at his own expense.

Industry Canada (ICES-003): This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Any changes or modifications to the display not expressly approved by Planar could void the user's authority to operate this equipment.

Other Certifications: CE

Summary of Contents for c50RP





















Reviews: