background image

F2 

ELECTRICAL POWER SUPPLY 

The unit must be powered from a single-phase power line according to the 
rated values indicated in table F.
The maximum acceptable variations from the electrical parameters are:

Voltage:    

+/- 5% 

of the nominal value 

Frequency:   +/- 2% 

of the nominal value

 

Power from lines with values outside of the indicated limits can damage the 
electrical components. 

 

F3 

WORKING CYCLE 

The motors are intended for continuous use. 
Under normal operating conditions they can function continuously with no 
limitations. 

F4 

FLUIDS PERMITTED 

OIL  :  VISCOSITY from 20 to 500 cSt. 

F5 

FLUIDS NOT PERMITTED 

FLUIDS

 

RELATED DANGERS:

 

Gasoline 

fire  - explosion 

Inflammable liquids with PM < 55°C 

fire - explosion 

Water 

pump oxidation 

Liquid food products 

contamination of the same 

Corrosive chemical products 

pump corrosion 
injury to persons 

Solvents 

fire - explosion 
damage to gasket seals 

G

 

HANDLING AND TRANSPORT 

Given the limited weight and size, the use of lifting devices is not required. 

DEPUROIL was carefully packed before shipment. Check the packing 
material on delivery and store in a dry place. 

Summary of Contents for DEPUROIL













Reviews: