Pioneer VSX-933 Instruction Manual Download Page 53

Page: 53 / 131

≫

≫

≫

≫

≫

≫

Playing Back

Perform the following procedure when this unit is on.

1. Switch the input on the TV to the input connected to the unit.

Start the server (Windows Media

Player 11, Windows Media

Player 12, or

NAS device) containing the music files to play.

3. Make sure that the PC or NAS is properly connected to the same network as

this unit.

Press NET to display the network service list screen.

•

If the "NET" indicator on the display blinks, the unit is not properly

connected to the network. Check the connection.

With the cursors, select "Music Server", and then press ENTER.

Select the target server with the cursors, and press ENTER to display the

items list screen.

• This unit cannot access pictures and videos stored on servers.

NET

/ / /

ENTER

Network

Inputs

HDMI 1

HDMI 2

HDMI 3

INPUT

TV’s REMOTE

The illustration shows an image.

Summary of Contents for VSX-933




































































































































Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands

Pioneer VSX-933, Instruction Manual

Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands